Compressor Knowledge

Compressor Fails to Build Pressure

Compressor Fails to Build Pressure: Causes, Safe Troubleshooting Steps, and When to Call for Service

Key points at a glance

  • Four fault scenarios lead to very different causes: no pressure build-up, slow pressure build-up, pressure drop under load, and a difference between compressor and consumer.
  • First record, then intervene: operating status, exact wording of the message, operating hours, and pressure readings at generation and consumer, ideally simultaneously and under the relevant demand.
  • Much can be narrowed down without intervening in the machine — via displays, differential pressure at the filters, and a check of open drains and fittings within the scope of operational release.
  • Raising the pressure setpoint is not a solution to an unexplained fault. An adjustment requires a technical assessment, an approval, and consideration of the limits of the entire system.
  • For a service request, the series and serial number, operating hours, the exact wording of the message, and the observed pressure trend are sufficient.

Shift begins, the station starts up — and the pressure gauge remains below the usual value. In production, the first machines report insufficient pressure. Anyone who merely acknowledges and restarts at this point loses time and often overwrites precisely the information that would have been necessary for troubleshooting. This article concerns screw compressors in a fixed compressed air station, not small piston units in the workshop.

“No pressure” is not a single fault, but an observation that fits several causes. It can be due to the machine, the receiver, the treatment, or the piping network — and in some cases, the measuring point itself. If this is not clarified within a few troubleshooting steps, calling service is quicker than another restart attempt.

The following discusses distinguishing between fault scenarios, what can be read during ongoing operation, and the points at which the system should be shut down.

Four Fault Scenarios, Four Directions for Investigation

The distinction determines where to look. It takes a few minutes and often saves an entire troubleshooting process.

1. No Pressure Build-Up

If the drive is running but the pressure is not building, the machine may not be operating under load. Oil-lubricated screw compressors regulate via an inlet regulator: in idle mode, the intake side is largely closed, the drive continues to rotate, but hardly any air is delivered. The operating manual for the machine indicates the status displayed by the control system for this. The second possibility is an open point in the system — a manual drain at a low point, a fitting in the wrong position, or a consumption point that remained open overnight.

2. Pressure Rises Too Slowly

Here, the machine is delivering, but the balance is incorrect. A clogged intake filter increases resistance on the suction side. Leaks continuously draw air from the network. And in some operations, demand has grown over years without the supply volume ever being recalculated — how to accurately determine compressed air demand is a better starting point than an estimate. For belt-driven versions, belt slip is an additional cause.

3. Pressure Drops Under Load

If the pressure only drops during specific operations and then recovers, the problem lies in the interplay of demand profile, usable storage, and control strategy. How long a peak can be covered by the receiver depends on its volume, the usable pressure range, the demand, and whether air is simultaneously being delivered. Whether the machine goes back on load or the motor restarts are two different processes with different timings. This can only be reliably assessed with a measured load profile.

4. Pressure at the Compressor, but Not at the Consumer

This observation shifts suspicion towards the network and treatment — but it does not rule out the generation unit. Only when both readings are taken simultaneously and under the demand at which the problem occurs can a true pressure difference be separated from a control, capacity, or display issue. If a difference is then actually shown, the usual sources of loss come into question: clogged filters, the dryer, pipes that are too long or too narrow, hoses, and couplings at the consumer. The article on compressed air treatment describes which components in this chain contribute to this.

Compressor fails to build pressure

What Should Be Recorded Before Any Intervention

Any change to the setpoint or the system also alters the fault scenario. If you note things down beforehand, you won’t have to search twice later:

  • Series, model designation, and serial number from the type plate.
  • Total operating hours, as well as load and idle hours, if provided by the control system.
  • Displayed operating status and the exact wording of any message with date and time.
  • Pressure reading at generation and at the critical consumer, simultaneously and under the relevant demand.
  • Set pressure values of the control system and the receiver volume of the station.
  • Since when the behaviour has been noticed and what changed before that — new machine, network modification, maintenance, filter change.

Read, Observe, Classify

The following overview helps you classify observations, narrow down possible causes, and coordinate the next step with service.

The table assigns observations to possible causes and indicates what can be read without intervening in the machine. The operating manual and operational release regulate which actions are permissible during operation. The table does not replace troubleshooting on the specific system.
Observation Possible Causes What can be read or observed When service takes over
The machine is running, but the pressure is not rising. Operation in idle mode; demand exceeds supply; an open consumption point or an open drain. Read operating status and messages on the control system. Check visible valve and drain positions within the scope of operational release. If load status is present, no open consumption point is found, and pressure still does not rise.
Pressure rises more slowly than in comparable previous situations. Higher intake resistance; leaks in the network; increased demand; belt slip in belt-driven systems. Read filter and differential pressure gauges. Compare load and idle hours with previous values. During a production break, listen for audible leaks. If wear is suspected on the drive, compressor stage, control valves, or separator.
Pressure drops during load peaks and then recovers. Relationship between demand profile, usable storage, and control strategy; a single large consumer. Record the time, magnitude, and duration of drops and correlate them with the production schedule. Compare readings at generation and consumer. If storage, pressure settings, or the distribution of multiple machines need to be evaluated.
Pressure is present at the compressor, but absent at the consumer. Pressure loss via treatment, pipes, hoses, and couplings. A measurement or display error is also possible. Readings at generation and consumer simultaneously and under the relevant demand. Record differential pressure readings of the filters. If the difference remains after a filter change, the measurement is unclear, or the network structure needs to be changed.
The control system displays a message or shuts down. Warning, maintenance message, or activation of a safety function. This cannot be distinguished solely from its occurrence. Note the exact wording of the message with date, time, and operating hours, and refer to the operating manual. Immediately for safety shutdowns and repeated shutdowns. For other messages, the documented machine reaction applies.

Where the Search Ends

Some measures provide short-term pressure and either shift the problem or create a new one:

  • Opening pressure-bearing components before the system has been depressurised and secured against restart according to manufacturer specifications.
  • Bypassing, adjusting, or blocking safety functions, interlocks, or safety valves.
  • Repeatedly acknowledging a shutdown to force operation.
  • Raising the pressure setpoint without technical assessment and approval.
  • Working on electrical equipment without appropriate qualification.

The operating manual of the specific machine is authoritative. If a troubleshooting step described there deviates from this description, the manufacturer’s information applies. And if the fault could be due to the compressor room itself — temperature, supply air, installation — the checklist for the installation room helps in narrowing it down.

If the Cause Lies in the Network

Raising the setpoint until enough pressure reaches the consumer is common but rarely a solution. Energy consumption usually increases, as do leakage losses, and the cause remains undetected. The reliable approach goes in the other direction: the required pressure is determined at the consumer, then tolerances and actual losses via treatment and network are added. How a justified operating pressure can be derived from this is described in detail elsewhere.

Condensate also belongs in this consideration. A condensate drain that remains permanently open continuously draws air from the system and appears as a leak in the pressure trend. How condensate forms in the machine and what damage it causes there is described separately.

Frequently Asked Questions

May I raise the pressure setpoint until enough pressure is restored?

Not as a reaction to an unexplained fault. An adjustment of the setpoint is a technical decision: it presupposes that the cause has been assessed, that the limits of the machine, receiver, treatment, and network are maintained, and that the change is operationally approved. Without these steps, it conceals the problem and generally increases energy consumption.

How do I know if the machine is running in idle mode?

By the displayed operating status. The designation and representation differ depending on the series and version; the binding assignment is in the machine’s operating manual.

How much leakage is normal?

There is no universally valid value for this. The question becomes meaningful through a measurement in real operation, for example, via compressed air consumption during non-production times. Experience from another plant does not replace this measurement.

Does the system have to shut down immediately for every message?

No — but the message decides that, not intuition. Safety shutdowns and repeated shutdowns must be evaluated before the machine restarts. For warning and maintenance messages, the reaction documented in the operating manual applies. It cannot be inferred from the mere occurrence of a message which case is present.

Narrow Down the Fault

If simple checks do not provide a clear picture, a brief technical discussion usually yields more than another restart attempt. For an initial assessment, four pieces of information are sufficient: series and serial number, operating hours, the exact wording of the message, and the observed pressure trend with time. This allows determining whether the machine, receiver, or network is more likely to need checking, and what measurement would be sensible next.